Extensions and Torque Wrenches Myth Busted – https://thefartiste.com

Do Extensions Affect Torque Wrench Accuracy:

The short answer is no, extensions do not affect torque wrench accuracy. That is if they’re used properly, and you’re using your torque wrench correctly. In order to get an accurate reading from a torque wrench, you must always place your hand in the correct spot, maintain the torque wrench parallel to the fastener at all times, and avoid any wobble or universal (swivel) sockets. It besides very important to use a high-quality torsion wrench that has been calibrated recently .

Torque Wrench Myths Busted Here, But First A Pop Quiz For You

You are using your 1/2″ drive click type torsion wrench for your lug nuts on your fresh 1987 Honda Accord .
You already googled the properly stuff nut torsion values. Sweet ! An easy to read mesa :
Screen Shot 2018 09 03 at 9.32.51 AM

Ok, perfect you set your mark raw amazing torsion wring you bought to 80ft-lbs. You already have an amazing torsion wrench because you read my article on what torsion wrenches to buy .
then, you grab your 6 1/2″ extension so that you can clear your new rims. You start tightening the lug nuts in a star practice as you learned on youtube when person walks up behind you .
Screen Shot 2018 09 03 at 10.29.36 AMIt’s your friend, Mark, who sees you torquing down your new sweet wheels and comes over to watch.
It ’ s your supporter, Mark, who sees you torquing down your new sugared wheels and comes over to watch. He is much older and apparently wiser than you, and you ’ ve seen him in his driveway working on all his cars. You hope you ’ ra doing it right as he watches, when he abruptly spurts out .
“Did you adjust your torque values with that extension?” he asks cleverly .
“ Wait, what ? ” you reply backing away from what you were doing .
“Using an extension or an adapter on a torque wrench changes the torque values. You probably just way over torqued your wheels” he states as fact.
“ But, hey I got to go, good be careful you don ’ thymine separate any lug bolts or lose a wheel on the expressway. That happened to a new technical school at my shop class that used an extension on his torsion twist, customer about died. ”
He laughs as he walks away, content with his helpfulness. Ok, possibly this rather rude neighbor doesn ’ thyroxine exist. But people giving out bad car repair advice like it is candy is nothing new .

Anyone that has worked on their car in their own driveway has dealt with the professional technician neighbor coming by to drop some wisdom.

You take a step second and reevaluate why you even bought a fixer-upper car in the first place .
How did you ever think you ’ d be able to actually work on it ? tied something simple you seem to mess up. Gosh, you think, I better foreswear while I am ahead. I should just drive over to the local Wal Mart and have them torque the wheels .
Your friend told you to take the extension off and fair try your best not to scratch up your sweet new rims .
You follow his advice .
That night after you drive home defeated with your new scratched up odoriferous rims, and bloodied knuckles, you decide to do some research .
You google “ Using an annex on a torsion wrench. ”
You’re blown away by what you find. Had everything you learned about respecting your elders been false?

The physics behind torque wrenches and extensions:

Screen Shot 2018 09 03 at 10.32.16 AMTurns out your ASE certified master tech friend was wrong. But could it in truth be ? That dang guy named Newton who talked about physics was right?!
Turns out your ASE certified maestro technical school friend was wrong.That dang guy named Newton who talked about physics was right ? ! Is it very the biggest myth about torsion wrenches to ever be perpetrated by everyone that has worked on cars, my self included?
Yup. And it literally continues to be a beginning of sharpen debate in the on-line community. Right behind Synthetic versus Regular Oil, Using RTV correctly, or putting Anti Seize on modern flicker plugs .
Buckle astir. Sit back, and enjoy the ride .
Turns out that the physics behind torsion and torsion wrenches do not agree with your friend ’ randomness statement. I must apologize for besides telling people this over the years .
Extensions and step-down adapters (1/2″ to 3/4″ etc) do not change the torque value applied. however, we must take a deeper look to in truth understand the physics behind torsion, using torsion wrenches, and how to be a chic DIYer / technician .

The biggest myth when using torque wrenches is that using adapters and extensions changes the applied torque value:

Extensions and Adapters do not change the applied torque as long as some general principles are understood/used. 
“ No, it won ’ triiodothyronine reduce the torsion. Torque is equivalent to radius x force. a long as A, the force is applied at the same distance from the nut/bolt that you ’ ra tighten and B, it ’ mho applied in the lapp focus then you ’ ll be applying the like torsion. An arranger ( specially so short ) shouldn ’ t have a detectable effect on the guidance that you ’ re applying the force. fortunately, you don ’ t have to measure your radius ( animal foot ) adam force ( pound ) because the torsion wrench will do that for you .
The one concern with using more than a couple of adapters is that the possibility of introducing a significant change in the fish between the torsion wrench and bolt/nut face becomes more plausible .
The torque wrench should be parallel to the face of whatever you’re torquing for the measurement to be accurate. ” Read more here .

Adapters and Extensions if used properly do not affect torque values:

For the rest of the discussion, you can think of adapters and extensions as the same concept. Going from 1/2″ drive to a 3/8″ socket does not change the torque value simply because of stepping down the drive size. However, it is important to use high-quality adapters/extensions as this kind of twisting forces can break/shatter sockets.

Some educational video I have picked through and chosen that exemplify this point very well. Remember we are talking about extensions and adapters that do not swivel or universals .
You will see in the video but if your torsion wrench has certain types of universals in trace and the torsion wrench or extensions aren ’ deoxythymidine monophosphate kept straight then the power will change .
hera precisely watch it is easier to see than to try to visualize it :

& More In Depth :

& even More To Prove The like Points :

Where you place your hand on the torque wrench matters the most:

Why does your hand position affect torque wrench values:

Any force that is applied that international relations and security network ’ thymine at a 90-degree angle will change the apply torsion to the fastener. Watch the videos above to see this in carry through .
Screen Shot 2018 09 03 at 10.23.44 AMIt is much easier to visualize than to explain by writing. Once you have an understanding check out this calculator for calculating torque value changes depending on different angles/lengths of your torque It is a lot easier to visualize than to explain by writing. once you have an reason check out this calculator for calculating torsion value changes depending on different angles/lengths of your torsion wrench here Increase the length of the torque wrench, and you change the applied torque.
A.k.a crows feet (as shown in the image on the left) or extensions used in order to reach hard to reach fasteners in the engine bay. Watch this video (cued up for you) where he uses another type of extension that lengthens his torque wrench. Therefore, he must recalculate the torque values.

However, the torque values will not be affected if you keep the extension at a 90-degree angle. 

Looking at the image above it is easier to visualize. When the crows foot is pointed straight out it increases the length of the torque wrench and therefore changes the torque value.
However, when it is at the 90-degree angle it is the same distance from the bolt to the end of the handle (L) is the same. Therefore the torque value is NOT EFFECTED. 
If It changes the effective length of the torque wrench then it will change the torque value. If you keep it at 90 degrees to the torque wrench then your torque readings will be the same and consistent. It DOES NOT matter how long your extension is, only that it is kept at a 90-degree angle and the effective length of the torque wrench isn’t changed. 

Using Cheater Bars on Torque Wrenches ( Especially Click Type ) :

Avoid doing this at all costs. It will change the torsion interpretation ( on a snap type wrench ) I am not sure on a nonclick type wrench. From CDI a high-level torsion wrench party on their web site, under department of education, ( link here ) they say specifically :
Screen Shot 2018 09 03 at 10.47.22 AMI do know that on click type torque wrenches adding a cheater bar will throw off your torque values by a lot.

Also, every manual for every torque wrench tells you to put your hand in the grip area.
If you move your hand up and down the torque wrench you will affect the torque rating.
here is the region in the television where he shows how a deceiver bar is impacting the torsion values :

Since this is just good practice, I don’t care if it doesn’t effect a digital torque wrench (IT DOES ON A CLICK TYPE) therefore just don’t do it. You shouldn’t need to anyways.
Screen Shot 2018 09 03 at 10.03.28 AM
Screen Shot 2018 09 03 at 10.03.19 AM
Screen Shot 2018 09 03 at 10.03.02 AM
Screen Shot 2018 09 03 at 10.02.47 AM

The Main Thing People Mess Up Is not Using A High-Quality Torque Wrench :

A torque wrench should be calibrated every year at least in the automotive world. 
Treat it like a glass egg, if you drop it should be checked for its calibration. Does that really apply if you’re just doing lug nuts? No. If you don’t feel any noticeable difference, and you know it was right before, then it doesn’t really matter if you’re torquing lug nuts with a margin of error. You’ll be able to feel tight / know if it isn’t right. 
It gets actually important however when you ’ re rebuilding engines, torquing very specific bearings and so forth, that is when all these concepts in truth come into play. Without a well calibrated torsion wrench you may be means off, and the read/write head gasket won ’ triiodothyronine hold up etc etc .
You can send it in, or call around dealerships in your area and ask the service guys if they can check your torque wrench / adjust it. It will likely cost more than if you bought a harbor freight special in the first place.
That is why I highly encourage you to at least get the next level up from harbor freight (if you can afford it). 

I Asked Aviation Mechanics How Torque Wrenches Are Handled In Their field :

The answer is pretty cool/enlightening to how important calibrated tools are in their field. 
From a exploiter on Reddit :
“ Tool see is extremely important in aerospace. My company, for exercise, is in the serve of doing away with personally owned tools. They bought crazy self-conscious toolboxes from snapshot on that you need a badge to open and it scans the draftsman after you take a creature out, keeping cut of who has the tool and what plane they are working on .
Screen Shot 2018 09 03 at 2.33.57 PMTools like torque wrenches, multimeters, spring scales, etc all have to be calibrated on specific schedules.
Tools like torsion wrenches, multimeters, spring scales, etc all have to be calibrated on particular schedules. If any of those tools were used on a problem I performed, I have to document what the tool ID number is and when it is adjacent due for calibration .
evening before they got rid of personal cock boxes, no tools that require calibration could be owned by the individual, even if they were presently calibrated. They could only be owned by the company and observe in the instrument room .
These are my companies policies, and they are a tad on the extreme point english, but they aren ’ t that far off of the cosmopolitan idea. ”

To see Snap On’s ATC Level 5 (highest level of security tool box in action):

What Torque Wrenches Do I Recommend in 2018:

To read more about torsion recommendations ( and towards the end ) my recommendations in 2018 chatter here .
now you can use a torsion wrench like a emboss, and not feel bad grabbing the largest reference you have and still getting those lug nuts absolutely tight !
In case you don ’ deoxythymidine monophosphate find like reading I have picked out my favorites for value/ durability/accuracy on Amazon :
All automotive technicians should first start with a 1/2″ Torque Wrench and breaker bar. (Buy this CDI one if you can afford it)
then if you need to do much smaller demand farce grab a 1/4″ Torque Wrench
And if you silent find the need for a 3/8″ Torque Wrench pick that up after you have the 1/4 & 1/2″ drive. 

DO YOU LIKE THIS ARTICLE:
informant : https://thefartiste.com
Category : Tech

About admin

I am the owner of the website thefartiste.com, my purpose is to bring all the most useful information to users.

Check Also

articlewriting1

Manage participants in a zoom meeting webinar

Call the people who attend the meet as follows Alternate host host Who scheduled the …

Leave a Reply

Your email address will not be published.