Breaking News

# How to choose a power supply for your LED strip project | Waveform Lighting

LED strips, unfortunately, are not as simple as traditional incandescent light bulbs when it comes to installation and set up. Because they run on low voltage DC, they require a power supply device that converts 120V/240V AC (depending on your location) into the voltage signal that LED strips can use. Below is our simple, no-stress, 3-step guide that will help you select a power supply.

As an example, let’s suppose that you’ve found the following LED strip product:

## Step 1: Determine the LED strip voltage

The first step is to figure out what the voltage of the LED strip is. The majority of LED strips available on the market run at 12V DC. Others are primarily at 24V DC.

In the case of WenTop’s product, we find it listed in the product description:

…as well as the specifications listed further below:

If you still aren’t sure, another way to confirm this is to look at the product photo. Most LED strips will have a mark showing 12V or 24V.

Now, check if the voltage on the power supply specifications matches the LED strip. In this case, the power supply is also 12V, so we are good to go.

Also confirm that the input voltage on the AC side matches your country’s voltage (120V for North America, etc).

Bonus tip: if you have a power supply lying around at home, for example, you can also check the backside label and see if the voltage is listed there.

## Step 2: Determine the power draw of the LED strip

Next, look for either a wattage (W) or amperage (A) specification for the LED strip. This could be listed as either W/m or A/m, or simply W or A.

The LED strip lists the total wattage as 24 Watts, or 4.8 Watts per meter. This checks out, because there are 5 meters per reel, and 4.8 Watts/meter * 5 meters = 24 Watts.

Although it’s not listed here, we can calculate the amperage using the formula P = V x A, where P is the wattage, V is voltage and A is amperage. To solve for A (amperage), simply plug in 24 for wattage and 12 for voltage, and calculate:

24 = 12 x A

A = 2.0 Amps.

In electrical terms, we now know that at 12V, this LED strip will draw about 24 Watts per reel (5 meters), or about 2.0 Amps.

Now, let’s check the power supply.

We see that it has a rating of 36W, or 3A. Again, if we use the formula P = V x A, this checks out, because it is a 12V power supply.

What this means is that this power supply is capable of supplying up to 36 Watts, or about 3.0 Amps.

Because the power supply’s capacity is higher than the LED strip’s power draw, we can safely conclude that these two products can be paired together.

Power supply wattage and amperage ratings can confuse and even scare some people. It isn’t unreasonable to assume that a power supply that pumps 36 Watts into a 24 Watt LED strip would cause damage. Furthermore, what if you decided to one day cut that LED strip in half, turning it into a 12 Watt LED strip?

This is why we emphasize capable and capacity above. Just because a power supply has a rating of 36 Watts does not mean that it will necessarily supply that much power. On the contrary, the power supply will actually supply as little as is needed, and match the power draw based on what is hooked up to it. If the power draw exceeds the power supply capacity, however, then the power supply can experience abnormal operation and damage.

Therefore, this power supply can be used to power any LED strip that draws between 0 Watts and 36 Watts.

## Step 3: Determine the connection method

The power supply will likely come with a power connector as shown below:

You will likely see this specified as 5.5 mm x 2.1 mm. Be careful as 5.5 mm x 2.5 mm may not work with LED strip plugs.

Find out if the LED strip reel comes with a DC plug like this:

If so, it should be compatible with the power supply plug, and you can directly plug the power supply into the wall on one end, and into the LED strip on the other end.

On the other hand, if you are looking to cut up your LED strip into multiple segments, or if the entire reel comes with just two bare wires (typically red & black) like this:

In this case, you’ll need to

## A-Series LED Bulbs

Our A19 and A21 lamps fit in standard lamp fixtures and are perfective for deck and desk lamp fixtures .

## Candelabra LED Bulbs

Our candelabrum LED light bulb extend soft and warm light output in a cosmetic bulb stylus that fits E12 lamp fixtures .

## BR30 LED Lamps

BR30 lamps are ceiling lamps that fit in residential and commercial fixtures with 4-inch or across-the-board openings .

## T8 LED Lamps

directly replace 4-ft fluorescent lamps with our T8 LED tube lights, compatible both with and without ballasts .

LED tube light fixtures pre-wired and compatible with our T8 LED lamps .

## LED Linear Fixtures

analogue lamp fixtures in 2-ft and 4-ft lengths. Plugs into standard wall outlets north dakota mounts using screws or magnets .

## LED Shop Lights

viewgraph light fixtures with suspension chains. Plugs into standard rampart outlets .

## UV-A LED Lights

We offer 365 nm and 395 new mexico LED lights for fluorescence and cure applications .

## UV-C LED Lights

We offer 270 new mexico UV-C LED lights for bactericidal applications .

## LED Modules & Accessories

LED PCBs, panels and other form factors for a variety show of industrial and scientific applications .

## LED Strip Lights

Bright LED emitters mounted on a flexible circuitboard. Can be cut-to-length and installed in a kind of locations .

## LED Strip Dimmers

Dimmers and controllers to adjust LED strip lighting system brightness and color .

## LED Strip Power Supplies

Power supply units to convert line electric potential to moo electric potential DC needed for LED strip unaccented systems .

## Aluminum Channels

Extruded aluminum distribution channel profiles for mounting LED strip lights .

## LED Strip Connectors

Solderless connectors, wires and adapters to join and connect LED plunder light system components together .

beginning : https://thefartiste.com
Category : Tech

I am the owner of the website thefartiste.com, my purpose is to bring all the most useful information to users.

## Manage participants in a zoom meeting webinar

Call the people who attend the meet as follows Alternate host host Who scheduled the …